如何在FreeSWITCH开源软交换安装Sangoma-A400模拟卡

发布网友发布时间：2022-04-24 11:46

共2个回答

热心网友时间：2022-04-13 16:34

FreeSWITCH 是目前非常流行的开源软交换平台，支持IPPBX，软交换调度，IVR系统，呼叫中心等等解决方案，同时支持PSTN的接入方式。Sangoma 模拟语音卡可以通过FreeTDM 模块和freeSWITCH 实现通信。
准备工作
检测板卡配件，确认板卡的RJ11 配线，sangoma 附件配置包含了RJ11 的窄头线。
如果支持FXS，板卡必须上电。如果A400 无FXS 也需要上电。并且检测12V 电脑电源接口
插入模拟板卡，确认支持PCI-E 或者PCI卡
通过系统命令 lspci 检查系统是否检测到语音板卡，执行系统命令，lspci -vvv，可以看到如下结果：
05:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card
Subsystem: NEC Corporation Device 1300
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 255 (1250ns min, 3750ns max)
Interrupt: pin A routed to IRQ 185
Region 0: Memory at f7200000 (32-bit, non-prefetchable) [size=K]
解压压缩包
tar xfz wanpipe-current.tgz
cd wanpipe-<version>.tgz

编译板卡驱动和freetdm
执行编译安装命令
make freetdm
make install

下载安装配置FreeSWITCH
安装linux Centos 支持包
yum install expat-devel openssl-devel libtiff-devel libX11-devel unixODBC-devel libssl-devel python-devel \
zlib-devel libzrtpcpp-devel alsa-lib-devel libogg-devel libvorbis-devel perl-libs gdbm-devel \
libdb-devel uuid-devel @development-tools

安装git 以后，使用git 安装 freeSWITCH
安装FreeSWITCH
git clone git://git.freeswitch.org/freeswitch.git
cd freeswitch
./bootstrap.sh

编译前，添加freetdm 模块，编辑moles.conf 文件，注释掉libs/freetdm/mod_freetdm 模块，保存文件。执行
./configure
make
make install
make all install cd-sounds-install cd-moh-install // 安装语音文件和语音等待文件

配置Sangoma 板卡文件
执行 /usr/sbin/wancfg_fs 命令，启动配置脚本，通过选项来一步步配置板卡
[root@localhost sbin]# wancfg_fs
########################################################################
# Sangoma Wanpipe #
# Dahdi/Zaptel/SMG/TDMAPI/BOOT Configuration Script #
# v2.39 #
# Sangoma Technologies Inc. #
# Copyright(c) 2013. #
########################################################################

Would you like to change FreeSWITCH Configuration Directory?
Default: /usr/local/freeswitch/conf
1. NO
2. YES
[1-2, ENTER='NO']:1 // 选择默认安装目录

-------------------------------------------------------
Configuring T1/E1 cards [A101/A102/A104/A108/A116/T116]
-------------------------------------------------------

No Sangoma ISDN T1/E1 cards detected

Press any key to continue:
-------------------------------------------
Configuring ISDN BRI cards [A500/B500/B700]
-------------------------------------------

No Sangoma ISDN BRI cards detected

Press any key to continue:
------------------------------------
Configuring GSM cards [W400]
------------------------------------

No Sangoma GSM cards detected

Press any key to continue:
------------------------------------
Configuring analog cards [A200/A400/B600/B610/B700/B800]
------------------------------------

-----------------------------------------------------------
A400 detected on slot:4 bus:3
-----------------------------------------------------------

Would you like to configure AFT-400 on slot:4 bus:3
1. YES
2. NO
[1-2]:1 // 选择yes

Which codec will be used?
1. MULAW - North America
2. ALAW - Europe
[1-2]:2 // ALAW

Which Operation Mode will be used?
1. FCC
2. TBR21
3. AUSTRALIA
[1-3, ENTER='FCC']: 1 // 无中国制式，暂时选择FCC。如果修改到中国制式，修改/etc/wanpipe/wanpipe1.conf 文件的 TDMV_OPERMODE = CHINA

Press any key to continue:
AFT-400 configured on slot:4 bus:3 span:1

Analog card configuration complete

Press any key to continue:
------------------------------------
Configuring USB devices [U100]
------------------------------------

###################################################################
# SUMMARY #
###################################################################

0 T1/E1 port(s) detected, 0 configured
0 ISDN BRI port(s) detected, 0 configured
1 analog card(s) detected, 1 configured
0 GSM card(s) detected, 0 configured
0 usb device(s) detected, 0 configured

Configurator will create the following files:
1. Wanpipe config files in /etc/wanpipe
2. freetdm config file /usr/local/freeswitch/conf/freetdm.conf
3. freetdm_xml config file /usr/local/freeswitch/conf/freetdm.conf.xml

Your configuration has been saved in /etc/wanpipe/debug-2013-07-31.tgz.
When requesting support, email this file to techdesk@sangoma.com

###################################################################

Configuration Complete! Please select following:
1. YES - Continue
2. NO - Exit
[1-2]:1 // 选择继续

Wanpipe configuration complete: choose action
1. Save cfg: Stop Wanpipe now
2. Do not save cfg: Exit
[1-2]:1 // 选择立即停止wanpipe

sh: asterisk: command not found
sh: asterisk: command not found

Stopping Wanpipe...

Removing old configuration files...

Copying new Wanpipe configuration files...

Copying new freetdm configuration files (/usr/local/freeswitch/conf/freetdm.conf)...

Copying new freetdm configuration files (/usr/local/freeswitch/conf/autoload_configs/freetdm.conf.xml)...

Wanrouter start complete...
Current boot level is 3

Wanrouter boot scripts configuration...

Removing existing wanrouter boot scripts...OK
Would you like wanrouter to start on system boot?
1. YES
2. NO
[1-2]:1 // 选择系统自动启动

Verifying Zaptel boot scripts...
Enabling wanrouter boot scripts ...(level:8)
Enabling wanrouter shutdown scripts ...(level:91)
Sangoma cards configuration complete, exiting...

[root@localhost sbin]# reboot

Broadcast message from root (pts/1) (Wed Jul 31 20:13:04 2013):

The system is going down for reboot NOW!
[root@localhost sbin]#

检测板卡硬件
执行以下命令，检查板卡状态，先执行命令：wanrouter start，然后执行以下命令：
[root@localhost ~]# wanrouter hwprobe

-------------------------------
| Wanpipe Hardware Probe Info |
-------------------------------
1 . AFT-A400-SH�0�2: SLOT=4�0�2: BUS=3�0�2: IRQ=5�0�2: CPU=A�0�2: PORT=PRI�0�2: HWEC=0�0�2: V=11

Sangoma Card Count: A200=1

[root@localhost ~]#
[root@localhost bin]# wanrouter status

Devices currently active:
wanpipe1

Wanpipe Config:

Device name | Protocol Map | Adapter | IRQ | Slot/IO | If's | CLK | Baud rate |
wanpipe1 | N/A | A200/A400/B600/B700/B800/B610| 169 | 4 | 1 | N/A | 0 |

Wanrouter Status:

Device name | Protocol | Station | Status |
wanpipe1 | A-ANALOG | N/A | Connected |

[root@localhost bin]#

检查配置freetdm.conf文件
这是FreeTDM 配置文件.
编辑：/usr/local/freeSWITCH/conf/freetdm.conf 文件
[span wanpipe FXO]
name => freetdm
trunk_type => fxo
group => grp2
fxo-channel => 1:7
number => 29193553 // 必须设置线路电话号码

trunk_type => fxo
group => grp2
fxo-channel => 1:8
number => 29193554 // 必须设置线路电话号码

编辑/usr/local/freeswitch/conf/tones.conf�0�2文件，添加支持中国忙音，拨号音
[cn]
generate-dial => v=-7;%(1000,0,450)
detect-dial => 450
generate-ring => v=-7;%(1000,4000,460)
detect-ring => 460
generate-busy => v=-7;%(350,350,460)
detect-busy => 460
generate-attn => v=0;%(100,100,1400,2060,2450,2600)
detect-attn => 460
generate-callwaiting-sas => v=0;%(300,0,440)
detect-callwaiting-sas => 460
generate-callwaiting-cas => v=0;%(80,0,2750,2130)
detect-callwaiting-cas => 460
detect-fail1 => 913.8
detect-fail2 => 1370.6
detect-fail3 => 1776.7
编辑freetdm.conf.xml
autoload_configs/freetdm.conf.xml
<configuration name="freetdm.conf" description="FreeTDM Configuration">
<settings>
<param name="debug" value="4"/>
<param name="hold-music" value="$${moh_uri}"/>
</settings>

<analog_spans>
<span name="FXS">

<param name="dialplan" value="XML"/>
<param name="context" value="fxs-ports"/>
<param name="enable_callerid" value="true"/> 
</span>
<span name="FXO">
<param name="dialplan" value="XML"/>
<param name="context" value="public"/>

<param name="tonegroup" value="cn"/> // 设置到中国制式
<param name="enable_callerid" value="true"/>
</span>
</analog_spans>
</configuration>

在默认的FreeSWITCH 启动模块中添加添加freetdm 模块
编辑文件 vi /usr/local/freeswitch/conf/autoload_configs/moles.conf.xml 删除注释，确认freetdm 模块已经被添加
<load mole="mod_freetdm"/>

检查ftdm 模块加载状态
运行 fs_cli 命令，进入到freeSWITCH CLI
freeswitch@internal> ftdm list
+OK
span: 1 (FXO)
type: analog
physical_status: ok
signaling_status: UP
chan_count: 2
dialplan: XML
context: public
dial_regex:
fail_dial_regex:
hold_music:
analog_options: none
freeswitch@internal> ftdm mp 1 1
span_id: 1 // 逻辑组
chan_id: 1 // 逻辑端口，呼入呼出的拨号规则中使用此端口
physical_span_id: 1 // 物理组
physical_chan_id: 7 // 物理端口位置
physical_status: ok
physical_status_red: 0
physical_status_yellow: 0
physical_status_rai: 0
physical_status_blue: 0
physical_status_ais: 0
physical_status_general: 0
signaling_status: UP
type: FXO
state: DOWN
last_state: HANGUP
txgain: 0.00
rxgain: 0.00
cid_date:
cid_name:
cid_num:
ani:
aniII:
dnis:
rdnis:
cause: NONE
session: (none)

-- States -- -- Function -- -- Location -- -- Time Offset --
RING => HANGUP [channel_on_hangup] [mod_freetdm.c:590] 0ms
HANGUP => DOWN [ftdm_analog_channel_run] [ftmod_analog.c:562] 515ms
DOWN => DIALING [analog_fxo_outgoing_call] [ftmod_analog.c:62] 161968ms
DIALING => UP [ftdm_analog_channel_run] [ftmod_analog.c:509] 7900ms
UP => HANGUP [channel_on_hangup] [

确认freetdm 模块已经加载。

热心网友时间：2022-04-13 17:52

全部栏目

如何在FreeSWITCH开源软交换安装Sangoma-A400模拟卡